Search results for " Boundary"
showing 10 items of 686 documents
Complex structural contribution of the morphotropic phase boundary in Na0.5Bi0.5TiO3 - CaTiO3 system
2019
Abstract The correlation between structure and dielectric properties of lead-free (1-x)Na0.5Bi0.5TiO3 - xCaTiO3 ((1-x)NBT - xCT) polycrystalline ceramics was investigated systematically by X-ray diffraction, combined with impedance spectroscopy for dielectric characterizations. The system shows high miscibility in the entire composition range. A morphotropic phase boundary (MPB), at 0.09 ≤ x
Temperature Coefficients of Crystal Defects in Multicrystalline Silicon Wafers
2020
This article investigates the influence of crystallographic defects on the temperature sensitivity of multicrystalline silicon wafers. The thermal characteristics of the implied open-circuit voltage is assessed since it determines most of the total temperature sensitivity of the material. Spatially resolved temperature-dependent analysis is performed on wafers from various brick positions; intragrain regions, grain boundaries, and dislocation clusters are examined. The crystal regions are studied before and after subjecting the wafers to phosphorus gettering, aiming to alter the metallic impurity concentration in various regions across the wafers. Most intragrain regions and grain boundarie…
How Gettering Affects the Temperature Sensitivity of the Implied Open Circuit Voltage of Multicrystalline Silicon Wafers
2019
The temperature sensitivity of the open circuit voltage of a solar cell is mainly driven by changes in the intrinsic carrier concentration, but also by the temperature dependence of the limiting recombination mechanisms in the cell. This paper investigates the influence of recombination through metallic impurities on the temperature sensitivity of multicrystalline silicon wafers. Spatially resolved temperature dependent analysis is performed to evaluate the temperature sensitivity of wafers from different brick positions before and after being subjected to phosphorus diffusion gettering. Local spatial analysis is performed on intra-grain areas, dislocation clusters and grain boundaries. Lar…
Variable-charge method applied to study coupled grain boundary migration in the presence of oxygen
2009
International audience; One of the important differences between simulation and experiments in grain boundary (GB)-dominated metallic structures is the lack of impurities such as oxygen in computational samples. A modified variable-charge method [Elsener A, Politano O, Derlet PM, Van Swygenhoven H. Modell Simul Mater Sci Eng 2008;16:025006] based on the Streitz and Mintmire approach [Streitz FH, Mintmire JW. Phys Rev B 1994;50:11996] is used to study coupled GB motion in an Al bicrystal with a [1 1 2] symmetrical tilt GB in the presence of substitutional O, and compared with the stick–slip process identified by Cahn and Mishin [Cahn JW, Mishin Y, Suzuki A. Acta Mater 2006;54:4953]. It is found…
Ion track template technology for fabrication of CdTe and CdO nanocrystals
2020
Abstract CdTe and CdO nanocrystals were synthesized by chemical deposition into a-SiO2/n-Si ion track template formed by 200 MeV Xe ion irradiation with the fluence of 108 ions/cm2. Depending on the temperature of the solution CdTe + CdO and single-phase CdO with a hexagonal crystal structure were obtained, respectively. The study of the current – voltage characteristics of the obtained structure with the single-phase CdO allows us to estimate the number of grain boundaries and the height of the potential barrier, as well as the n-type conductivity.
A comparative study on the compatibility of liquid lead–gold eutectic and liquid lead–bismuth eutectic with T91 and SS 316LN steels
2012
Abstract Liquid lead–gold eutectic (LGE) is considered as a potential target material for high power spallation sources. In the present work, the corrosion effects of LGE on T91 and SS 316LN steels have been investigated in comparison with that of liquid lead–bismuth eutectic (LBE) under the same testing conditions. Two tests were conducted at 400 °C for 1800 h and at 450 °C for 1300 h, in which specimens of the two steels were exposed to 1 m/s flowing LGE and LBE. Surface inspections showed that the specimens underwent a mixed corrosion mode of dissolution and oxidation. The results obtained from the SS 316LN specimens are very interesting. Firstly, EDX (electron energy dispersion X-ray sp…
The Grain Boundary Wetting Phenomena in the Ti-Containing High-Entropy Alloys: A Review
2021
In this review, the phenomenon of grain boundary (GB) wetting by melt is analyzed for multicomponent alloys without principal components (also called high-entropy alloys or HEAs) containing titanium. GB wetting can be complete or partial. In the former case, the liquid phase forms the continuous layers between solid grains and completely separates them. In the latter case of partial GB wetting, the melt forms the chain of droplets in GBs, with certain non-zero contact angles. The GB wetting phenomenon can be observed in HEAs produced by all solidification-based technologies. GB leads to the appearance of novel GB tie lines Twmin and Twmax in the multicomponent HEA phase diagrams. The so-cal…
Transport properties of Bi2Sr2Ca2Cu3O10+δ Bicrystal Grain Boundary Josephson Junctions and SQUIDs
1996
Josephson junctions and SQUIDs on 36.8° SrTiO 3 bicrystal substrates were prepared from epitaxial Bi 2 Sr 2 Ca 2 Cu 3 O 10+δ thin films with critical temperatures around 95K. The current-voltage characteristics are well described by the resistively and capacitively shunted junction model. I c R n products of 50μV at 77K and 0.7mV at 4.2K have been reached. The I c (B) dependence is symmetric to B = 0 with an I c suppression of 90% in the first minimum. Nevertheless it turns out, that the junctions are inhomogeneous on a μm scale. SQUID modulations observed at 78K indicate a flux-voltage transfer function of 2.7μV/Φ 0 at this temperature.
Structure and dielectric properties at phase transition of Na1/2Bi1/2TiO3-BaTiO3 solid solutions
2016
ABSTRACTPhase coexistence region is studied by x-ray diffraction for Na1/2Bi1/2TiO3-BaTiO3 solid solutions in the tetragonal phase side from the morphotropic phase boundary. The first order ferroelectric phase transition, determined from a jump in the temperature dependence of dielectric permittivity, is located inside the coexistence region of cubic and tetragonal phases and is below the temperature, where tetragonality disappears. At low BaTiO3 concentrations phase transition into ferroelectric state at cooling is slowly approached in time and is smeared over large temperature range. Rietveld method, applied for more precise evaluation of phase content, reveals large local deformations in…
ZnMgO-based UV photodiodes: a comparison of films grown by spray pyrolysis and MBE
2016
Detecting the UV part of the spectrum is fundamental for a wide range of applications where ZnMgO has the potential to play a central role. The shortest achievable wavelength is a function of the Mg content in the films, which in turn is dependent on the growth technique. Moreover, increasing Mg contents lead to an electrical compensation of the films, which directly affects the responsivity of the photodetectors. In addition, the metal-semiconductor interface and the presence of grain boundaries have a direct impact on the responsivity through different gain mechanisms. In this work, we review the development of ZnMgO UV Schottky photodiodes using molecular beam epitaxy and spray pyrolysis…